Points Needing Attention in the Production of Flexible PCB



👉https://www.jrpanel.com/R

The manufacture of flexible PCBs involves several complicated steps, and extreme care must be taken. Some design or manufacturing defects can cause the entire circuit board to fail.


During the PCB manufacturing process, please follow the precautions listed below:


1. Use the right type and quantity of materials to maintain "flexibility". For example, if an application requires a 6-layer rigid-flex PCB that will bend during assembly and then should be kept in a fixed position, the correct type of copper and adhesive must be used.


2. It is recommended to keep the circuit small. It is better to use a set of smaller circuits rather than a single larger circuit.


3. It is not a good habit to bend flexible circuits around corners. However, some design situations require bending at the corners. In this case, you can make a gentle bend or use a conical radius bend.


4. The copper used in the 6-layer rigid-flex board is easy to fall off the substrate. Therefore, it is essential to provide support for the copper to prevent its separation. Even if you are using surface mount pads and non-plated pads, you should consider using them with some other measures, such as fixing the cover mask to the pads.


5. The recommended tolerances must be adhered to as closely as possible.


6. It is best to avoid laying traces on each copper layer in the same direction. It is recommended to stagger the wiring to distribute the tension between the copper layers evenly.


7. It is recommended to carry a power or ground plane on the flexible circuit to enhance/maintain the flexibility of the circuit board. You can consider using solid copper casting or shaded polygons.


In order to produce reliable rigid-flex based products, you must be careful enough to pay attention to details. Otherwise, the final assembly may not provide the expected functionality and durability. By following the above recommendations, these troublesome situations can be avoided.

评论

发表评论

此博客中的热门博文

How to Read Circuit Diagrams for Beginners

图片
     👉 https://www.jrpanel.com/R This articles shows how to read circuit diagrams for beginners in electronics. Learn to read electrical and electronic circuit diagrams or schematics. A drawing of an electrical or electronic circuit is known as a circuit diagram, but can also be called a schematic diagram, or just schematic. Circuit or schematic diagrams consist of symbols representing physical components and lines representing wires or electrical conductors. In order to learn how to read a circuit diagram, it is necessary to learn what the schematic symbol of a component looks like. It is also necessary to understand how the components are connected together in the circuit. Battery and Light Bulb Circuit Probably the simplest circuit that can be drawn is one that you may have seen in a school science class: a battery connected to a light bulb as shown below. Simple Circuit Diagram for Beginners Circuit Symbols and Physical Components Each electronic or electrical compon...
阅读全文

In JRPanel, Manual Color Toning Is High-precision Craftsmanship

图片
  The production of membrane switches requires the participation of the printing process. A screen printing machine is required for printing. The quality of the product printing depends on the printing operation process and the details of the printing. Among them, manual toning is the most important step .  Only the precise control of the proportion of each color can produce the color that the customer needs.   Toning is a very knowledgeable craft. There are three main colors. These three colors can decorate the membrane switch perfectly. The three colors are red, yellow, and blue. Other colors can be obtained by mixing any two of these three colors. For example, yellow plus blue to green. When mixing colors with colors, pay attention to thoroughly mixing the inks, so that the inks are thoroughly mixed together to avoid color inconsistency, resulting in incoordination of the membrane switch panel. After the color is adjusted, it needs to be compared. The color and gl...
阅读全文

Smart PCB Manufacturing-the Next Stage of Advancement in Safety Equipment

图片
  Cities around the world are developing rapidly, crime is more difficult than ever, criminals are smarter than ever, and citizens’ property is threatened. The number of smart technologies on display has shown unprecedented signs of growth: video surveillance, attack and anti-theft alarm systems, access control, fire alarm and voice alarm technologies are all expanding.   With the advent of the Internet of Things, custom PCB manufacturing is now more popular than ever. Equipment manufacturers will be forced to make a safety-critical gadget in their bid to innovate and remain competitive. Aerospace, defense, automotive, medical and industrial control are only part of the vertical industry, with the growth of increased capabilities for device interconnection and remote collaborative work. This article attempts to explain how PCBs can make life easier for the monitoring team. How PCB-based electronic monitoring equipment promotes market development through its unparalleled vigila...
阅读全文